The JX-3P Matrix Upgrade features:-
•
1024 Tones & 8 Sequences can be stored and edited, Sequences can be optionally linked to tones. It is also possible to edit any Tone or Seq.
•
A Pulse Width Module is included with the Kiwi3P Matrix. This allows Pulse Width control and waveform mixing.
•
After tuning during the Kiwi-3P Matrix upgrade install a Saw wave tuning offset keeps the wave shape correct for all voices across the full range. Due to component
tolerances this is not possible on the original JX-3P hardware.
•
A Chorus Control board is included with the Kiwi3P Matrix. This allows variable Chorus Rate and manual control.
•
Saw, Pulse Width & Square Waveforms can be solo or mixed in any combination.
•
Sysex support for all and MidiCC for most parameters, Midi Sysex support for Tone Dump & Load
•
Patch Editor Control of Parameters (requires PE v 8.3 or later)
•
MidiQuest 12 includes editors for all the Kiwi range and it will work with any midi editor. The manual has full midi details.
•
Full Matrix system with 29 Source and 40 Destination types.
•
Key Assign Modes are Poly Single, Poly Dual, Poly Triple, Unison & Solo
•
Each Key Assign mode can have Rotate/Reassign, Staccato/Legato, Steal/No Steal with five steal modes (Highest, Lowest, Oldest, Newest, Quietest)
•
Portamento in all key modes
•
Note Detune available in all key modes, DCO 1 & 2 have separate Tune controls (±12 semitones) and DCO2 has a Fine Tune (±50 cents). There is also an Analogue
Feel parameter that adds a small random detune to notes.
•
Master Synth Fine Tune adjust in both hardware and software.
•
Three independent envelope generators. These are traditional ADSR type and are modeled on the Original JX-3P. Each ENV Mod can select from ENV 1 - 3 and has
an Inverted or Normal modes. These are faster than the traditional JX-3P envelopes and are matrix sources.
•
Three independent Low Frequency Oscillators with 6 waveforms each. Each LFO Mod can select from LFO 1-3 and they are a matrix source. LFOs can be plus and
minus base note or plus base note only.
•
Midi Note Aftertouch (Channel & Note), Midi and Internal Modulation Level and Midi Note Dynamics are all Matrix sources and can be sent any Matrix Destination.
•
LFO Button is a Matrix Source and can inject mod control to any matrix destination.
•
Bend Lever is coded to DCO Frequency for Bend but is also a Matrix Source which can be sent to any Destination
•
Front panel editing is available for all parameters. These can be edited via midi or the PG-200 (supported only).
•
Master, Sequencer and Arpeggiator clocks can optionally display on the front panel
•
Key transpose allows transposition to any key. The range for this is -1 Octave to +2 Octaves
•
CHORD MODE
•
Any chord with up to 6 notes can be set and played from any key
•
ARPEGGIATOR
•
The Arpeggiator is clocked from the Master Clock and can be independently divided to Half Note, Quarter Note, 1/8 Note, 1/8 Note Half Swing, 1/8 Note Full Swing, 1/8
Note Triplets, 1/16 Note, 1/16 Note Half Swing, 1/16 Note Full Swing, 1/16 Note Triplets, 1/32 Note, 1/32 Note Triplets, 1/64 Note.
•
Arp modes are Up, Down, Up and Down, Random, As Played, 1, 2, 3 or 4 octaves
•
Arp can be Started, Stopped & Continued using Midi Commands
•
Appeggiator will Output Midi Data
•
SEQUENCER
•
8 separate 124 Max step Polyphonic sequences can be created and stored
•
Sequences can be edited
•
The Sequencer is clocked from the Master Clock and can be independently divided to Half Note, Quarter Note, 1/8 Note, 1/8 Note Half Swing, 1/8 Note Full Swing, 1/8
Note Triplets, 1/16 Note, 1/16 Note Half Swing, 1/16 Note Full Swing, 1/16 Note Triplets, 1/32 Note, 1/32 Note Triplets, 1/64 Note.
•
Sequencer can be Started, Stopped & Continued using Midi Commands
•
Sequencer will Output Midi Data
•
PG-200
•
PG-200 support where possible (see manual)
•
PG-200 will output midi data
How much is my shipping?
Shipping is automatically calculated before you submit your payment information. Simply add items to your cart and proceed to the checkout page, where you'll be offered shipping options and their prices. In the UK it's normally around £4 for order values under £150, and free above that. Shipping to mainland EU is typically between £7 and £20, depending on the shipping method and the size and weight of the order.
Do you ship to my country?
Almost certainly - the site will give you an estimate of shipping costs if you add an item to the cart and then enter your country and postcode. If you have specific requirements (such as if you prefer UPS over FedEx, for example) then let us know in advance and we'll try to work something out for you.
Shipping methods
We use a combination of Parcelforce, DPD, Royal Mail and UPS for the UK, and for international orders it's either Royal Mail, UPS, DHL or FedEx depending on where you are in the world. If you have a particular preference then try to let us know BEFORE you order so we can look into it for you. Please note that there may occasionally be additional shipping charges if you live in a remote area, depending on what surcharges are applied by the shipper. We'll get in touch to discuss this with you in such cases.
Dispatch times
For UK orders, we normally dispatch the same working day if we get the order before 15:00. If you have a really urgent situation then of course drop us an email before ordering and we'll always do our absolute best to accommodate you.
For international orders, we normally dispatch the same day if we get the order before 13:00 but again, occasionally it might be the next day before we can send it out, and sometimes FedEx or UPS may come a little earlier than scheduled which would also push an order into the next day.
Shipping times
Since April 2020 the couriers we use have suspended guarantees for shipping times, so even though we're paying them for priority services - 24-48 hours for most of the world - in practice it's often an extra day on top and sometimes it can be longer.
There is absolutely nothing we can do about this unfortunately. If you are outside the UK and it's a life-or-death situation where you absolutely MUST have that passive mult for the next day then... it may be better to find a local supplier.
Saturday shipping
If you're in the UK and you order before 15:30 on a Friday then we can send something for a Saturday delivery (NB: this applies to UK mainland addresses only). The success rate with DPD is about 95% so it's worth a punt most of the time. Please note that if you select Saturday shipping on an order placed earlier in the week, we'll wait until Friday to ship it.
Pre-orders
If a product is listed as a pre-order, it means we've ordered it from the supplier but it's not physically in stock yet. The product listing will include an estimated shipping date based on the best information we have from the supplier, but do bear in mind this is subject to change and is not a guaranteed date.
If you place an order containing a mixture of in-stock and pre-order items, we'll normally hold off on shipping anything until the pre-order item(s) have arrived, rather than splitting it into multiple shipments. If you need the in-stock items sooner, we'd recommend placing separate orders. As always, please get in touch if you have questions.
Product Overview
The JX-3P Matrix Upgrade features:-
•
1024 Tones & 8 Sequences can be stored and edited, Sequences can be optionally linked to tones. It is also possible to edit any Tone or Seq.
•
A Pulse Width Module is included with the Kiwi3P Matrix. This allows Pulse Width control and waveform mixing.
•
After tuning during the Kiwi-3P Matrix upgrade install a Saw wave tuning offset keeps the wave shape correct for all voices across the full range. Due to component
tolerances this is not possible on the original JX-3P hardware.
•
A Chorus Control board is included with the Kiwi3P Matrix. This allows variable Chorus Rate and manual control.
•
Saw, Pulse Width & Square Waveforms can be solo or mixed in any combination.
•
Sysex support for all and MidiCC for most parameters, Midi Sysex support for Tone Dump & Load
•
Patch Editor Control of Parameters (requires PE v 8.3 or later)
•
MidiQuest 12 includes editors for all the Kiwi range and it will work with any midi editor. The manual has full midi details.
•
Full Matrix system with 29 Source and 40 Destination types.
•
Key Assign Modes are Poly Single, Poly Dual, Poly Triple, Unison & Solo
•
Each Key Assign mode can have Rotate/Reassign, Staccato/Legato, Steal/No Steal with five steal modes (Highest, Lowest, Oldest, Newest, Quietest)
•
Portamento in all key modes
•
Note Detune available in all key modes, DCO 1 & 2 have separate Tune controls (±12 semitones) and DCO2 has a Fine Tune (±50 cents). There is also an Analogue
Feel parameter that adds a small random detune to notes.
•
Master Synth Fine Tune adjust in both hardware and software.
•
Three independent envelope generators. These are traditional ADSR type and are modeled on the Original JX-3P. Each ENV Mod can select from ENV 1 - 3 and has
an Inverted or Normal modes. These are faster than the traditional JX-3P envelopes and are matrix sources.
•
Three independent Low Frequency Oscillators with 6 waveforms each. Each LFO Mod can select from LFO 1-3 and they are a matrix source. LFOs can be plus and
minus base note or plus base note only.
•
Midi Note Aftertouch (Channel & Note), Midi and Internal Modulation Level and Midi Note Dynamics are all Matrix sources and can be sent any Matrix Destination.
•
LFO Button is a Matrix Source and can inject mod control to any matrix destination.
•
Bend Lever is coded to DCO Frequency for Bend but is also a Matrix Source which can be sent to any Destination
•
Front panel editing is available for all parameters. These can be edited via midi or the PG-200 (supported only).
•
Master, Sequencer and Arpeggiator clocks can optionally display on the front panel
•
Key transpose allows transposition to any key. The range for this is -1 Octave to +2 Octaves
•
CHORD MODE
•
Any chord with up to 6 notes can be set and played from any key
•
ARPEGGIATOR
•
The Arpeggiator is clocked from the Master Clock and can be independently divided to Half Note, Quarter Note, 1/8 Note, 1/8 Note Half Swing, 1/8 Note Full Swing, 1/8
Note Triplets, 1/16 Note, 1/16 Note Half Swing, 1/16 Note Full Swing, 1/16 Note Triplets, 1/32 Note, 1/32 Note Triplets, 1/64 Note.
•
Arp modes are Up, Down, Up and Down, Random, As Played, 1, 2, 3 or 4 octaves
•
Arp can be Started, Stopped & Continued using Midi Commands
•
Appeggiator will Output Midi Data
•
SEQUENCER
•
8 separate 124 Max step Polyphonic sequences can be created and stored
•
Sequences can be edited
•
The Sequencer is clocked from the Master Clock and can be independently divided to Half Note, Quarter Note, 1/8 Note, 1/8 Note Half Swing, 1/8 Note Full Swing, 1/8
Note Triplets, 1/16 Note, 1/16 Note Half Swing, 1/16 Note Full Swing, 1/16 Note Triplets, 1/32 Note, 1/32 Note Triplets, 1/64 Note.
•
Sequencer can be Started, Stopped & Continued using Midi Commands
•
Sequencer will Output Midi Data
•
PG-200
•
PG-200 support where possible (see manual)
•
PG-200 will output midi data
Technical Specs
Shipping Details
How much is my shipping?
Shipping is automatically calculated before you submit your payment information. Simply add items to your cart and proceed to the checkout page, where you'll be offered shipping options and their prices. In the UK it's normally around £4 for order values under £150, and free above that. Shipping to mainland EU is typically between £7 and £20, depending on the shipping method and the size and weight of the order.
Do you ship to my country?
Almost certainly - the site will give you an estimate of shipping costs if you add an item to the cart and then enter your country and postcode. If you have specific requirements (such as if you prefer UPS over FedEx, for example) then let us know in advance and we'll try to work something out for you.
Shipping methods
We use a combination of Parcelforce, DPD, Royal Mail and UPS for the UK, and for international orders it's either Royal Mail, UPS, DHL or FedEx depending on where you are in the world. If you have a particular preference then try to let us know BEFORE you order so we can look into it for you. Please note that there may occasionally be additional shipping charges if you live in a remote area, depending on what surcharges are applied by the shipper. We'll get in touch to discuss this with you in such cases.
Dispatch times
For UK orders, we normally dispatch the same working day if we get the order before 15:00. If you have a really urgent situation then of course drop us an email before ordering and we'll always do our absolute best to accommodate you.
For international orders, we normally dispatch the same day if we get the order before 13:00 but again, occasionally it might be the next day before we can send it out, and sometimes FedEx or UPS may come a little earlier than scheduled which would also push an order into the next day.
Shipping times
Since April 2020 the couriers we use have suspended guarantees for shipping times, so even though we're paying them for priority services - 24-48 hours for most of the world - in practice it's often an extra day on top and sometimes it can be longer.
There is absolutely nothing we can do about this unfortunately. If you are outside the UK and it's a life-or-death situation where you absolutely MUST have that passive mult for the next day then... it may be better to find a local supplier.
Saturday shipping
If you're in the UK and you order before 15:30 on a Friday then we can send something for a Saturday delivery (NB: this applies to UK mainland addresses only). The success rate with DPD is about 95% so it's worth a punt most of the time. Please note that if you select Saturday shipping on an order placed earlier in the week, we'll wait until Friday to ship it.
Pre-orders
If a product is listed as a pre-order, it means we've ordered it from the supplier but it's not physically in stock yet. The product listing will include an estimated shipping date based on the best information we have from the supplier, but do bear in mind this is subject to change and is not a guaranteed date.
If you place an order containing a mixture of in-stock and pre-order items, we'll normally hold off on shipping anything until the pre-order item(s) have arrived, rather than splitting it into multiple shipments. If you need the in-stock items sooner, we'd recommend placing separate orders. As always, please get in touch if you have questions.
