The P1 is a dual channel pedal interface. It can be used for pedal or line level in and out or as a guitar or bass input as the pedal in is a high-Z input that will not suck the life out of the tone of your instrument as low impedance inputs can do.
The module is designed to have more than 100kHz bandwidth in both directions to give you a very clean interface with in and out impedance to work well with pedals.
The two halves of the module are independent. You can use it as a dual mono or as a stereo interface.
Eurorack to pedal level is attenuating -18dB and pedal to Eurorack level is amplifying 18dB.
There is soft controlled symmetrical clipping in both directions through the module so if you are driving the inputs hard it will not sound harsh. You can use this as a creative effect.
The unit is AC coupled to be able to isolate your Eurorack from whatever you connect on the pedal side.
Eurorack to pedal
The Eurorack input has a symmetrical soft clipping at +/-10V.
A 5V signal (+14dBV) will give you a -4dBV signal out on the pedal out side (0,6V).
Pedal to Eurorack
The pedal input expects max -4dBV in to give a 5V signal out on the Eurorack side. However, the signal that comes from a pedal, the direct signal from a guitar or some line level equipment may have transients that are higher than this. This even if you are careful about the levels you put into it.
Because of this a limiter with a super soft long knee has been designed into the module so you don’t have to worry about getting harsh distortion on the transients.
The limiter just starts touching the signal slightly at -4dBV in and reaches full compression and symmetrical brick wall limiting with +6dBV in (2V). The output brick wall limits to +/-10V.
The limiter circuit is designed not to touch the signal at all under normal operations, it is there to add protection and maybe a bit of warmth when your signal is above -4dBV in. It can of cause be driven as hard as you like for creative purposes.
Device specs
- Module size: 4 hp wide, 30 mm deep with power cable connected.
- Input impedance: 100 kohm on the Eurorack side. 1 Mohm on the pedal side.
- Output impedance: 1 kohm
- Bandwidth: More than 10 Hz to 100 kHz in both directions through the module.
- Power requirements: +/-12V. Max power consumption +/-19 mA
- Connect the power cable with the red stripe down towards the -12V marking.
- The unit is protected for reverse power.
How much is my shipping?
Shipping is automatically calculated before you submit your payment information. Simply add items to your cart and proceed to the checkout page, where you'll be offered shipping options and their prices. In the UK it's normally around £4 for order values under £150, and free above that. Shipping to mainland EU is typically between £7 and £20, depending on the shipping method and the size and weight of the order.
Do you ship to my country?
Almost certainly - the site will give you an estimate of shipping costs if you add an item to the cart and then enter your country and postcode. If you have specific requirements (such as if you prefer UPS over FedEx, for example) then let us know in advance and we'll try to work something out for you.
Shipping methods
We use a combination of Parcelforce, DPD, Royal Mail and UPS for the UK, and for international orders it's either Royal Mail, UPS, DHL or FedEx depending on where you are in the world. If you have a particular preference then try to let us know BEFORE you order so we can look into it for you. Please note that there may occasionally be additional shipping charges if you live in a remote area, depending on what surcharges are applied by the shipper. We'll get in touch to discuss this with you in such cases.
Dispatch times
For UK orders, we normally dispatch the same working day if we get the order before 15:00. If you have a really urgent situation then of course drop us an email before ordering and we'll always do our absolute best to accommodate you.
For international orders, we normally dispatch the same day if we get the order before 13:00 but again, occasionally it might be the next day before we can send it out, and sometimes FedEx or UPS may come a little earlier than scheduled which would also push an order into the next day.
Shipping times
Since April 2020 the couriers we use have suspended guarantees for shipping times, so even though we're paying them for priority services - 24-48 hours for most of the world - in practice it's often an extra day on top and sometimes it can be longer.
There is absolutely nothing we can do about this unfortunately. If you are outside the UK and it's a life-or-death situation where you absolutely MUST have that passive mult for the next day then... it may be better to find a local supplier.
Saturday shipping
If you're in the UK and you order before 15:30 on a Friday then we can send something for a Saturday delivery (NB: this applies to UK mainland addresses only). The success rate with DPD is about 95% so it's worth a punt most of the time. Please note that if you select Saturday shipping on an order placed earlier in the week, we'll wait until Friday to ship it.
Pre-orders
If a product is listed as a pre-order, it means we've ordered it from the supplier but it's not physically in stock yet. The product listing will include an estimated shipping date based on the best information we have from the supplier, but do bear in mind this is subject to change and is not a guaranteed date.
If you place an order containing a mixture of in-stock and pre-order items, we'll normally hold off on shipping anything until the pre-order item(s) have arrived, rather than splitting it into multiple shipments. If you need the in-stock items sooner, we'd recommend placing separate orders. As always, please get in touch if you have questions.
Product Overview
The P1 is a dual channel pedal interface. It can be used for pedal or line level in and out or as a guitar or bass input as the pedal in is a high-Z input that will not suck the life out of the tone of your instrument as low impedance inputs can do.
The module is designed to have more than 100kHz bandwidth in both directions to give you a very clean interface with in and out impedance to work well with pedals.
The two halves of the module are independent. You can use it as a dual mono or as a stereo interface.
Eurorack to pedal level is attenuating -18dB and pedal to Eurorack level is amplifying 18dB.
There is soft controlled symmetrical clipping in both directions through the module so if you are driving the inputs hard it will not sound harsh. You can use this as a creative effect.
The unit is AC coupled to be able to isolate your Eurorack from whatever you connect on the pedal side.
Eurorack to pedal
The Eurorack input has a symmetrical soft clipping at +/-10V.
A 5V signal (+14dBV) will give you a -4dBV signal out on the pedal out side (0,6V).
Pedal to Eurorack
The pedal input expects max -4dBV in to give a 5V signal out on the Eurorack side. However, the signal that comes from a pedal, the direct signal from a guitar or some line level equipment may have transients that are higher than this. This even if you are careful about the levels you put into it.
Because of this a limiter with a super soft long knee has been designed into the module so you don’t have to worry about getting harsh distortion on the transients.
The limiter just starts touching the signal slightly at -4dBV in and reaches full compression and symmetrical brick wall limiting with +6dBV in (2V). The output brick wall limits to +/-10V.
The limiter circuit is designed not to touch the signal at all under normal operations, it is there to add protection and maybe a bit of warmth when your signal is above -4dBV in. It can of cause be driven as hard as you like for creative purposes.
Device specs
- Module size: 4 hp wide, 30 mm deep with power cable connected.
- Input impedance: 100 kohm on the Eurorack side. 1 Mohm on the pedal side.
- Output impedance: 1 kohm
- Bandwidth: More than 10 Hz to 100 kHz in both directions through the module.
- Power requirements: +/-12V. Max power consumption +/-19 mA
- Connect the power cable with the red stripe down towards the -12V marking.
- The unit is protected for reverse power.
Technical Specs
Shipping Details
How much is my shipping?
Shipping is automatically calculated before you submit your payment information. Simply add items to your cart and proceed to the checkout page, where you'll be offered shipping options and their prices. In the UK it's normally around £4 for order values under £150, and free above that. Shipping to mainland EU is typically between £7 and £20, depending on the shipping method and the size and weight of the order.
Do you ship to my country?
Almost certainly - the site will give you an estimate of shipping costs if you add an item to the cart and then enter your country and postcode. If you have specific requirements (such as if you prefer UPS over FedEx, for example) then let us know in advance and we'll try to work something out for you.
Shipping methods
We use a combination of Parcelforce, DPD, Royal Mail and UPS for the UK, and for international orders it's either Royal Mail, UPS, DHL or FedEx depending on where you are in the world. If you have a particular preference then try to let us know BEFORE you order so we can look into it for you. Please note that there may occasionally be additional shipping charges if you live in a remote area, depending on what surcharges are applied by the shipper. We'll get in touch to discuss this with you in such cases.
Dispatch times
For UK orders, we normally dispatch the same working day if we get the order before 15:00. If you have a really urgent situation then of course drop us an email before ordering and we'll always do our absolute best to accommodate you.
For international orders, we normally dispatch the same day if we get the order before 13:00 but again, occasionally it might be the next day before we can send it out, and sometimes FedEx or UPS may come a little earlier than scheduled which would also push an order into the next day.
Shipping times
Since April 2020 the couriers we use have suspended guarantees for shipping times, so even though we're paying them for priority services - 24-48 hours for most of the world - in practice it's often an extra day on top and sometimes it can be longer.
There is absolutely nothing we can do about this unfortunately. If you are outside the UK and it's a life-or-death situation where you absolutely MUST have that passive mult for the next day then... it may be better to find a local supplier.
Saturday shipping
If you're in the UK and you order before 15:30 on a Friday then we can send something for a Saturday delivery (NB: this applies to UK mainland addresses only). The success rate with DPD is about 95% so it's worth a punt most of the time. Please note that if you select Saturday shipping on an order placed earlier in the week, we'll wait until Friday to ship it.
Pre-orders
If a product is listed as a pre-order, it means we've ordered it from the supplier but it's not physically in stock yet. The product listing will include an estimated shipping date based on the best information we have from the supplier, but do bear in mind this is subject to change and is not a guaranteed date.
If you place an order containing a mixture of in-stock and pre-order items, we'll normally hold off on shipping anything until the pre-order item(s) have arrived, rather than splitting it into multiple shipments. If you need the in-stock items sooner, we'd recommend placing separate orders. As always, please get in touch if you have questions.
